MyCarHelpline Forum for Premium Support !!

Get Professional Support from Experts. Ask your Question Now !!

  1. Aniket deshmukh
  2. Service & Maintenance
  3. Tuesday, February 27 2018
I have Hyundai Verna 1.6 sx model i getting problem that rpm is not passing 3000 and had an problem in pickup i consult with showroom and private mechanic so both said that I need to change wiring of car or have to check ecm so plz suggest me what to do
Mayank Tanwar Accepted Answer
0
Votes
Undo
Hello Aniket Deshmukh, if your car RPM goes down and not working well then do following steps:-

1.Check your fuel pump

2.Make it Throttle body clean

3.Make your injector clean

4.Check your RPM Sensor

5.Check your car Emulator

6.Check if there is any gas leakage near by your car engine.

Do All the above your car will be smooth and there will be no problem related to RPM.


  1. more than a month ago
  2. Service & Maintenance
  3. # 1
Pritam Kumar Accepted Answer
0
Votes
Undo
Plz check DRV in verna
  1. more than a month ago
  2. Service & Maintenance
  3. # 2
Shiva Accepted Answer
0
Votes
Undo
Plz check the air filter sensor im not pretty sure wat they call it.i have the same issue they charging 14000 for that sensor in hyundai....
  1. more than a month ago
  2. Service & Maintenance
  3. # 3
Babu cochin Accepted Answer
0
Votes
Undo
My verna fluidic was having check engine light blinking stationary.. At that time RPM was not going above 3000. I scanned and erased the sensor. scan result was rail presuure low for engine speed. After araiser rpm went above 3000 and was running smoothly. Now no engine light but rpm less that 3000 after one week of running. what can be . No lag on running below 3000 rpm.
  1. more than a month ago
  2. Service & Maintenance
  3. # 4
Ani Sharma Accepted Answer
0
Votes
Undo
My creta is not reving more than 5000 rpm does anyone had this problem if they did what was the solution (1.6sx petrol manual )


  1. more than a month ago
  2. Service & Maintenance
  3. # 5
Gopal Accepted Answer
0
Votes
Undo
My verna fludic 1.6 sx crdi starts well, well pick up but after some time rpm does not raise above 3000, and orange check light constant appears, I got scanned the engine found air flow less, got maas air flow censor replaced still same problem , can some friend guide me what to do ?
  1. more than a month ago
  2. Service & Maintenance
  3. # 6
Sandeep Accepted Answer
0
Votes
Undo
I am facing same problem with verna faludic desiel. RPM not passing 3000. Please advise me to fix this problem.
  1. more than a month ago
  2. Service & Maintenance
  3. # 7
Sam Accepted Answer
0
Votes
Undo
Hi there,
I have a hyundai verna crdi SX i have the same prblm so checked with service advisor in hyundai service center he sd rpm sensor issue and that needs to be replaced, the sensor cost is 14k....
  1. more than a month ago
  2. Service & Maintenance
  3. # 8
0
Votes
Undo
I have a hyundai verna xi 2008 madel have the same prblm car missing in running condition..
  1. more than a month ago
  2. Service & Maintenance
  3. # 9
abhi Accepted Answer
0
Votes
Undo
My self Abhilash,

Verna Fluidic 1.6 diesel engine 2012 model. I had a problem with RPM not passing above 3000, Hyundai service people said the sensor is not working My mass airflow sensor was bad, hopefully, I need to change the sensor which cost me around 17500 recently I did that in Aug 2020 & Now my RPM is working above 3000, but I don't see the pickup in my car even after changing the sensor. My 1st and 2nd gear pickup are very bad slow push hesitate to take pickup, 3r to 6th gear is better. Can someone help me what can be done?

I see a lot of comments saying that throttle body cleaning, EGR valve cleaning & Injector check, will solve the problem is that true pls help!
  1. more than a month ago
  2. Service & Maintenance
  3. # 10
Arham Accepted Answer
0
Votes
Undo
Plz check the air filter sensor im not pretty sure wat they call it.i have the same issue they charging 14000 for that sensor in hyundai....
dude your a life saver my car had the same problem can't rev upto 3000 and turns out the air filter sensor cuplar was loose just like you said, i plugged it in properly and my car is now back to normal
  1. more than a month ago
  2. Service & Maintenance
  3. # 11
Tauqir Accepted Answer
0
Votes
Undo
I have hyundai verna sx plus automatic 1.6 crdi diesel and my concern is when car is moving in 2 nd gear and shifting to 3 rd gear it feel pushing heavily, there is no engine check light .
What to do ..?
Plz
  1. more than a month ago
  2. Service & Maintenance
  3. # 12
Subodh thakur Accepted Answer
0
Votes
Undo
Please check the turbo charge pipe as some time in and out pipe during repier get interchanged...which cause the issue ....
  • Page :
  • 1


There are no replies made for this post yet.
Be one of the first to reply to this post!
Guest
Submit Your Response
Upload files or images for this discussion by clicking on the upload button below. Supports gif,jpg,png
• Remove Upload Files (Maximum File Size: 1 MB)
You may insert polls into your post. The poll would then appear in the post.
Vote Options
Captcha
Verify